## ABSTRACT

This study deals with the reliability and availability characteristics of two different systems,

the second system differs from the first system due to the additional feature of preventive

maintenance. Reliability and Availability analysis of system having one active unit and one

warm stand-by unit with self-reset function and one maintenance facility. The failure unit is

repaired through self-reset or maintenance according to different failure model.( Mean

Time to System Failure), Steady- State Availability, Busy Period Analysis and Profit

Function are derived for the two systems using linear first order differential equations. Two

systems were evaluated theoretically and graphically to observe the effect of preventive

maintenance on systems performance. The result finally shows that increase in failure rate

leads to decrease in MTSF, Steady-State Availability and Profit Function of figure 4.1, 4.2

and 4.3. It was also found that increase in repair rate leads to increase in MTSF, Steady-

State Availability and Profit Function of figure 4.4, 4.5, and 4.6. Therefore, the result

indicated that second system originate better reliability due to the additional feature of

preventive maintenance.

## TABLE OF CONTENTS

Title Page i

CERTIFICATION ii

DEDICATION iii

ACKNOWLEDGENTS iv

TABLE OF CONTENTS v

5

NOTATIONS/ABBREVIATIONS viii

LIST OF FIGURES x

ABSTRACT xi

CHAPTER ONE 1

1.0: GENERAL INTRODUCTION 1

1.1: Introduction 1

1.2: Background to the Study 2

1.3: Reliability Measures 3

1.3.1: Reliability 3

1.3.2: Mean Time to Failure 3

1.3.3: Failure Rate Function and Repair Rate Function 4

1.3.4: Maintainability and Availability 4

1.3.5: Mean Time to Failure (MTTF) and Mean Time Between Failure (MTBF) 5

1.3.6: Preventive Maintenance 5

1.4: Aim and Objectives 5

1.5: Scope and Limitation 6

1.6: Suggestions for Further Studies 6

CHAPTER TWO 7

2.0: LITERATURE REVIEW 7

2.1: Relationship between Availability, Reliability and Maintainability 7

2.2: Availability Classification 8

6

2.3: Standby Classification 9

CHAPTER THREE 18

3.0: RESEARCH METHODOLOGY 18

3.1: Introduction 18

3.2: Model Description and Assumptions 18

3.3: FIRST TRANSITION SYSTEM 19

3.4: SECOND TRANSITION SYSTEM 21

3.4.1: Mean Time to System Failure (MTSF1) 22

3.4.2: Steady-State Availability (

1

( ) T A ) 25

3.4.3: Busy Period Analysis (BP1) 27

3.4.4: Profit Function (PF1) 28

3.4.5: Mean Time to System Failure 2 (MTSF ) 29

3.4.6: Steady-State Availability

2

( ) T A 31

3.4.7: Busy period Analysis (BP2) 34

3.4.8: Profit Function (PF2) 36

CHAPTR FOUR 37

4.0: RESULT AND DISCUSSION 37

4.1: Introduction 37

4.1.1: Mean Time to System Failure 1 (MTSF ) 37

4.1.2: Steady-State Availability

1

( ) T A 38

7

4.1.3: Busy Period Analysis (BP1) 39

4.1.4: Mean Time to System Failure 2 (MTSF ) 39

4.1.5: Steady –State Availability

2

( ) T A 40

4.1.6: Busy Period Analysis 2 (BP ) 40

4.2: Discussion of Result 44

CHAPTER FIVE 46

5.0: SUMMARY AND CONCLUSSION 46

5.1: Summary 46

5.2: Conclusion 46

REFERENCES 47

## CHAPTER ONE

1.0 GENERAL INTRODUCTION

1.1 Introduction:

The role and importance of reliability have been a core of any engineering industry for the

last three decades. Reliability is of importance to both manufacturers and consumers. So,

the reliability measure is very important, as the improvement of reliability is achieved

through quality. While this measure of reliability assumes great importance in industry,

there are many situations where continuous failure free performance of the system, though

desirable may not be absolutely necessary, Yadavalli and Vanwyk (2012).

Several authors have studied a two (or more) similar and dissimilar unit standby redundant

system. Haggag (2009a), studied the cost analysis of dissimilar-unit cold-standby system

with three state and preventive maintenance using linear first order differential equations.

El-sherbeny et al (2009), studied the optimal system for series systems with warm standby

components and a repairable service station. Researchers in reliability have shown a keen

interest in the analysis of two (or more) component parallel system owing to their practical

utility in modern industrial and technological set ups.

Two unit warm standby redundant systems have been investigated extensively in the past.

The most general model is the one in which both the life time and repair time distributions

of the units are arbitrary. However the study of standby system with more than two units,

though very important, has received much less attention, possibly because of the built in

difficulties in analyzing them. Such systems have been studied only when either the life

time or the repair time is exponentially distributed. When both these are general, the

21

problem appears to be intractable even in the case of cold standby systems. The present

contribution is an improvement in the state of art in the sense that a three unit warm

standby system is shown to be capable of comprehensive analysis. In particular we show

that there are imbedded renewal points that render the analysis possible. Using these

imbedded renewal points they obtained the reliability and availability functions,

Srinivasan and Subramaniam (2006).

But In this research, the reliability and availability characteristics of two different systems

are study, where the second system differs from the first system due to the additional

feature of preventive maintenance. Each system consisting of one active unit and one warm

standby unit with self-reset function and maintenance facility. The failure unit is repaired

through self reset or maintenance according to different failure models.

1.2: Background to the Study

Reliability and availability are very important indices in a substation control protection

system. The Station Computer (SC) has important role in the system. Its function is to

maintain the central system data base and provide interfaces to the outsider world-locally to

station operators through the local Man Machine Interfaces (MMI) subsystem and remotely

to system operators and protection engineers through Supervisory Control and Data

Acquisition system (SCADA) communication interfaces. So, its reliability directly

influences the reliability of Station Computer (SC). Two units warm standby redundancy is

taken. Redundancy is one of the ways of improving the reliability of system when the

individual unit of the system remains unchanged. Warm standby is essential for two units to

switch within the shortest time. So, the active unit and warm standby unit run in different

22

states, which makes their failure rate different. Commonly, the failure rate of the warm

standby unit is smaller than that of the active one. So, compared with a hot standby system,

the reliability of the warm standby system is increased. Second, each unit has a self reset

function. Each unit performs automatic error detection through self – checking and recovers

from some failures, El-Said and El-Hamid (2006).

1.3: Reliability Measures

Reliability is the analysis of failures, their causes and consequences. It is the most

important characteristics of product quality as things have to be working satisfactorily

before considering other quality attributes. Usually, specific performance measures can be

embedded in to reliability analysis by the fact that if the performance is bellow a certain

level, a failure can be said to have occurred.

1.3.1: Reliability is the probability that the system will perform its intended function under

specified working condition for a specified period of time. Mathematically, the reliability

function R(t) is the probability that a system will be successfully operating without failure

in the interval from time zero to time t.

R(t) = P(T > t), t ≥ o

where T is a random variable representing the failure time or time – to failure. The failure

probability, or unreliability is then F(t) = 1- R(t), = P(T≤ t) which is known as the

distribution function of T.

1.3.2: Mean Time to Failure the mean time to failure (MTTF) is defined as the expected

value of the lifetime before a failure occurs.

23

1.3.3: Failure Rate Function and Repair Rate Function

The failure rate function, or hazard function, is very important in reliability analysis

because it specifies the rate of the system aging.

The Failure Rate Function: Is defined as the quantity representing the probability that a

device of age t will fail in the small interval from time t, to t + dt. The importance of failure

rate function is that it indicates the changing rate in the aging behavior over the life of a

population component.

Repair Rate Function: Is the expected time to repair the system from failure. This include

the time it takes to diagnose the problem, the time it takes to get a repair technician on site,

and the time it takes to physically repair the system, Pham (2003).

1.3.4: Maintainability and Availability

When a system fails to perform satisfactorily, repair is normally carried out to locate and

correct the fault. The system is restored to operational effectiveness by making an

adjustment or by replacing a component.

Maintainability: Is defined as the probability that a failed system will be restored to a

functioning state within a given period of time when maintenance is performed

according to prescribed procedures and resources. Generally, maintainability is the

probability of isolating and repairing a fault in a system within a given time.

Maintenance personnel have to work with system designers to ensure that the system

product can be maintained cost effectively.

24

The Availability Function of a system, denoted by A(t) is defined as the probability

that the system is available at time t. Different from the reliability that focuses on a

period of time when the system is free of failures, availability concerns at a time

point at which the system does not stay at the failed state.

Mathematically, A(t) = Pr(system is up or available at time instant t).

1.3.5: Mean Time to Failure (MTTF), and Mean Time Between Failure (MTBF) it is

important to distinguish between the concepts mean time to failure and mean time between

failures (MTBF). The MTTF is the expected time to failure of a component or system. That

is, the mean of the time to failure (TTF) for that component or system. The MTBF is the

expected time to failure after a failure and repair of the component or system.

1.3.6: Preventive Maintenance the maintenance carried out at predetermined intervals or

corresponding to prescribed criteria and intended to reduce the probability of failure or the

performance degradation of an item. Hoyland and Naws (1994).

1.4: Aim and Objectives

The main aim of this research work is to investigate and improve upon the existing

methodologies for the reliability and availability characteristics of two different systems,

where the second system differs from the first system due to the additional feature of

preventive maintenance. To achieve the above aim the following objectives are derived.

To observe the effect of failure rate, repair rate and preventive maintenance on both

system, in terms of their MTSF, Steady-State Availability and Profit Function.

**GET THE COMPLETE PROJECT»**

Do you need help? Talk to us right now: (+234) 8111770269, 08111770269 (Call/WhatsApp). Email: [email protected]

**IF YOU CAN’T FIND YOUR TOPIC, CLICK HERE TO HIRE A WRITER»**

Disclaimer: This PDF Material Content is Developed by the copyright owner to Serve as a RESEARCH GUIDE for Students to Conduct Academic Research. You are allowed to use the original PDF Research Material Guide you will receive in the following ways: 1. As a source for additional understanding of the project topic. 2. As a source for ideas for you own academic research work (if properly referenced). 3. For PROPER paraphrasing ( see your school definition of plagiarism and acceptable paraphrase). 4. Direct citing ( if referenced properly). Thank you so much for your respect for the authors copyright. Do you need help? Talk to us right now: (+234) 8111770269, 08111770269 (Call/WhatsApp). Email: [email protected]

*Related Current Research Articles*

Purchase Detail

Hello, we’re glad you stopped by, you can download the complete project materials to this project with Abstract, Chapters 1 – 5, References and Appendix (Questionaire, Charts, etc) for ~~N~~4000 ($15) only, To pay with **Paypal**, **Bitcoin** or **Ethereum**; please click here to chat us up via Whatsapp.

You can also call **08111770269** or **+2348059541956** to place an order or use the whatsapp button below to chat us up.

Bank details are stated below.

**Bank:** UBA

**Account No:** 1021412898

**Account Name:** Starnet Innovations Limited

### The Blazingprojects Mobile App

**Tags:**current project topics in mathematics education m.sc maths project topics in differential equations m.sc maths project topics in graph theory pdf m.sc maths project topics in linear algebra m.sc maths project topics in topology pdf m.sc project topics in maths maths project topics in algebra msc maths project topics in algebra msc maths project topics in algebra pdf msc maths project topics in complex analysis msc maths project topics in differential equations msc maths project topics in graph theory msc maths project topics in graph theory pdf msc maths project topics in linear algebra msc maths project topics in number theory msc maths project topics in numerical analysis msc maths project topics in operations research msc maths project topics in operations research pdf msc maths project topics in real analysis msc maths project topics in topology msc maths project topics in topology pdf project ideas on maths project topic in mathematics project topic in mathematics education project topics for applied mathematics project topics for bsc maths students project topics for mathematics students project topics for maths project topics for maths and statistics department project topics for maths for class 8 project topics for msc maths project topics in discrete mathematics project topics in financial mathematics project topics in fuzzy mathematics project topics in industrial mathematics project topics in mathematics and statistics project topics in mathematics department project topics in mathematics education for undergraduate project topics in mathematics education pdf project topics in mathematics for degree students project topics in mathematics for pg project topics in mathematics pdf project topics in maths education project topics in pure mathematics project topics on maths project topics on maths education project topics related mathematics undergraduate project topics in mathematics

## Recent Comments